RANGE OF PIN PUNCHES
For the AR-15 series of rifles.

GUN-SMITH PIN PUNCHES

£6.00p per set
£4.80p per set
Steel construction ~ silver.
2 & 2.4 inches / 50mm & 60mm long.
Weighs 24 grams.

£7.20p per set
£6.00p per set
Steel construction ~ black.
1.6 & 2.2 inches / 41mm & 56mm long.
Weighs 18 grams.

£9.60p per set
£7.20p per set
Steel construction.
3.5 inches / 88mm long.
Weighs 70 grams.

£9.60p per set
£7.20p per set
Stainless steel construction.
2.7 inches / 70mm long.
Weighs 48 grams.

£19.20p per set
£18.00p per set
Steel construction.
Range from 2.8 to 6.3" / 72 to 160mm long.
Weighs 358 grams.

£21.60p per set
£15.00p per set
Stainless steel and brass construction.
3 inches / 76mm long.
Weighs 255 grams.
General pin punch information:
Take down pin sets for AR series of rifles.
Knurled finger grips.
The 1/16" ~ bolt ejector/charging handle.
The 5/64" ~ gas tube.
The 3/32" ~ bolt catch/forward assist retaining.
The 1/8" ~ trigger guard.
- TWO PIECE SET ~ SILVER
Spring, detent / roll pin tool.
Made from high-quality steel with a zinc-plated finish, for rust prevention.
The two piece design, inserts and holds the detent and spring while the pivot pin is pushed in.
Aids in the faster installation / removal of the pivot spring and detent.
It also works as a roll pin punch and starter for the lower receiver roll pins.
Complete with keyring for safe storage.- TWO PIECE SET ~ BLACK
Spring, detent / roll pin tool.
Made from high-quality steel with a matt black oxide finish, for rust prevention.
Knurled grip section.
Aids in the faster installation / removal of the pivot spring and detent.
It also works as a roll pin punch and starter for the lower receiver roll pins.- FOUR PIECE SET ~ STEEL
The hollow end design helps to prevent damage caused from slipping whilst getting the pins started.
Black hardened steel set ~ 1/16", 5/64", 3/32", 1/8".- FOUR PIECE SET ~ STAINLESS STEEL
The hollow end design helps to prevent damage caused from slipping whilst getting the pins started.
Stainless steel set ~ 1/8", 5/32", 3/16", 7/32".- NINE PIECE SET ~ IN ROLL
Round head pin punches.
Made from 40CR steel.
Colour ~ black and silver.
Sizes ~ 1/16", 5/64", 3/32", 1/8", 5/32", 3/16", 7/32", 1/4", 5/16".
Complete in a handy red carry roll pouch.- NINE PIECE SET
The two smallest punches are made from stainless steel, and the others are brass.
Sizes:
Stainless steel ~ 1/16", 3/32".
Brass ~ 1/8", 5/32", 3/16", 7/32", 1/4", 9/32", 5/16".
Please Note: pin punches are generally considered a consumable product, they are not indestructible.
They will bend eventually, and faster if used on a stubborn pin.
It's best to use a tapered / drift starter pin punch in this case.
Usually it's extra hits rather than power of the hit that works best.
Then the correct weight of hammer is also an important factor.
Also available ~ Gunsmith Hammers.
TWO PIECE SET ~ SILVER:

TWO PIECE SET ~ BLACK:

FOUR PIECE SET ~ STEEL:

FOUR PIECE SET ~ STAINLESS STEEL:

NINE PIECE SET ~ IN ROLL:

NINE PIECE SET:
